Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 274 / 553

background image

NOTE

When a call starts and ends, the MG shows the start time and the end time based on the polarity reversal
on the subscriber line. The billing terminal that supports the polarity reversal charging function, such as a
charging phone set, implements the polarity reversal charging function based on the start time and the end
time of a call.

7.2.2.7 (Optional) Configuring the Attributes of the Ringing Current

You can adjust the ringing tone volume by modifying the attributes of the ringing current.
Generally, the attributes of the ringing current need not be modified. You need to modify the
attributes of the ringing current according to the local standards only when the default ringing
current attributes do not meet the local standards.

Context

The attributes of the ringing current include the following two parameters:

l

Ringing current frequency: The higher the frequency is, the sharper the ringing tones are.

l

AC voltage amplitude: The greater the amplitude is, the louder the ringing tones are.

The default settings of the attributes of the ringing current are as follows:

l

Ringing current frequency: 25 Hz

l

AC voltage amplitude: 65 Vrms

Procedure

Step 1

In the global config mode, run the

voip

command to enter the VoIP mode.

Step 2

Run the

ring attribute set

command to configure the attributes of the ringing current according

to the data plan.

Step 3

Run the

display ring attribute

command to check whether the attributes of the ringing current

are the same as the planned data.

----End

Example

To set the ringing current frequency to 16 Hz (parameter value 0) and AC amplitude to 65 Vrms
(parameter value 1), do as follows:

huawei(config)#

voip

huawei(config-voip)#

ring attribute set frequency 0 acamplitude 1

huawei(config-voip)#

display ring attribute

ringing current frequency : 16Hz
ringing current acamplitute: 65Vrms

7.3 Configuring the VoIP ISDN BRA Service

This topic describes how to configure the VoIP ISDN BRA service on an IP network. When the
MA5616 uses the H.248 protocol, the device supports the access of the ISDN BRA user. ISDN
technology provides end-to-end (E2E) digital connection and supports multiple types of voice
and non-voice telecom services.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

263

«
...
272
273
274
275
276
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Rabbit Страницы: 45

Бренд: Rabbit Страницы: 174

Бренд: Rabbit Страницы: 43

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: Qualys Страницы: 2

Бренд: Lancom Страницы: 25

Бренд: hilscher Страницы: 154

SLK-R602 Series

Бренд: Seriallink Страницы: 29

Бренд: National Instruments Страницы: 130

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: Variscite Страницы: 18

Бренд: UfiSpace Страницы: 32

Бренд: ExtraHop Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды