Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 276 / 553

background image

Table 7-20

Data plan for configuring the H.248-based VoIP ISDN BRA service

Item

Remarks

MG interface data
(The data must be
consistent with the
data on the MGC.)

Parameters of
the media
stream and
signaling
stream

Upstream
VLAN for
media and
signaling
streams

It is used as the upstream VLAN
of the VoIP service to be
configured. Standard VLAN is
recommended.

Uplink port for
media and
signaling
streams

It is used as the uplink port for the
VoIP service to be configured.

Media IP
address and
signaling IP
address

These IP addresses must be
contained in the media and
signaling IP address pools. The
media and signaling IP address
pools consist of all the IP
addresses of the L3 interface of
the upstream VLAN for media
and signaling streams.

Default IP
address of the
MG

It is the next hop IP address from
the MA5616 to the MGC.

Attribute
parameters of
the MG
interface

NOTE

There are
many MG
interface
parameters.
Only
mandatory
parameters
are listed here.
If the
mandatory
parameters
are not
configured,
the MG
interface
cannot be
started.

MG interface
ID

It is the ID of the MG interface
used by the VoIP service to be
configured. The MA5616
supports only one VAG.

Signaling port
ID of the MG
interface

It is the transport layer protocol
port ID used for the signaling
exchange between the MA5616
(AG) and the MGC.
The default signaling port ID
defined in H.248 is 2944 (text)
and 2945 (binary).

IP address of
the primary
MGC to which
the MG
interface
belongs

When dual homing is not
configured, you can configure the
parameters of only the primary
MGC. When dual homing is
configured, you also need to
configure the IP address and port
ID of the secondary MGC.

Port ID of the
primary MGC
to which the
MG interface
belongs

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

265

«
...
274
275
276
277
278
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: D-Link Страницы: 267

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

MegaRAID SATA 300-4XLP

Бренд: LSI Страницы: 3

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: Teknim Страницы: 10

Бренд: Grizzly Страницы: 9

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: ZyXEL Communications Страницы: 5

Бренд: Zonet Страницы: 53

Бренд: Supersonic Страницы: 46

Бренд: AOpen Страницы: 18

Бренд: ZALMAN Страницы: 8

OptiBond 210 C Series

Бренд: i-MO Страницы: 16

Бренд: ivideon Страницы: 11

Бренд: Hama Страницы: 24

Бренд: AES Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды