Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 334 / 553

background image

huawei(config)#

port vlan 50 0/0 0

Step 3

In the ADSL access mode, follow this procedure.
1.

Configure an ADSL2+ profile. For details, see

3.7.1 Configuring the ADSL2+ Profile

.

Here, the default ADSL2+ line template (line template 1) and the default ADSL2+ alarm
template (alarm template 1) are used as an example.

2.

Activate the ADSL port, and bind the ADSL2+ templates.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

In the ADSL access mode, bind the default ADSL2+ line template 1 and ADSL2+ alarm
template 1 to ADSL port 0/2/0.

huawei(config)#

interface adsl 0/2

huawei(config-if-adsl-0/2)#

deactivate 0

huawei(config-if-adsl-0/2)#

activate 0 template-index 1

huawei(config-if-adsl-0/2)#

alarm-config 0 1

huawei(config-if-adsl-0/2)#

quit

3.

Run the

display traffic table

command to query the existing traffic profiles in the system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-
index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri
2 512 18384 1024 36768 0 - tag-
pri
3 576 20432 1152 40864 2 - tag-
pri
4 64 4048 128 8096 4 - tag-
pri
5 2048 67536 4096 135072 0 - tag-
pri
6 off off off off 0 - tag-
pri

----------------------------------------------------------------------------
Total Num : 7

According to service requirements, the user access rate is 2048 kbit/s. The query result
shows that traffic profile 5 (for inbound and outbound rate limitation) meets the
requirements.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

323

«
...
332
333
334
335
336
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 10

Бренд: Laird Страницы: 36

Бренд: 3Com Страницы: 16

Бренд: Rolls Страницы: 2

Бренд: H3C Страницы: 12

Бренд: Radicom Страницы: 27

Бренд: E-Lins Страницы: 113

Бренд: SIIG Страницы: 20

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: ADDON Страницы: 4

Бренд: ExtraHop Страницы: 2

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды