Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 547 / 553

background image

NOTE

If no multicast subtending port is configured and multicast users are directly configured, the
maximum number of multicast users that each multicast user can demand is limited. If multicast
users are directly configured:

l

To set authentication of a multicast user, run the

igmp profile add

command to create a right

profile, run the

igmp profile

command to modify right parameters in the profile, and then run

the

igmp user bind-profile

command to bind the right profile to the multicast user.

l

To authenticate a multicast user, remove parameter

no-auth

when adding the multicast user.

The corresponding procedure is as follows:

huawei(config-btv)#

igmp user add service-port 1000 no-auth

huawei(config-btv)#

igmp user add service-port 1001 no-auth

huawei(config-btv)#

multicast-vlan 1000

huawei(config-mvlan1000)#

igmp multicast-vlan member service-port 1000

huawei(config-mvlan1000)#

igmp multicast-vlan member service-port 1001

11. Set the IGMP version.

Use IGMP V3.

huawei(config)#

multicast-vlan 1000

huawei(config-mvlan10000)#

igmp version v3

12. Select the IGMP mode.

Select the IGMP proxy mode.

huawei(config-mvlan10000)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

y

13. Configure the IGMP upstream port.

The IGMP upstream port is port 0/19/0 and works in the default mode, and protocol
packets are transmitted to all the IGMP upstream ports in the multicast VLAN.

huawei(config-mvlan10000)#

igmp uplink-port 0/19/0

14. Set the multicast global parameters.

In this example, the default settings are used for all the multicast global parameters.

15. Configure the program library.

The multicast IP address of the program is 224.1.1.10 and the IP address of the program
source is 10.10.10.10

huawei(config-mvlan10000)#

igmp program add name program1 ip 224.1.1.10

sourceip 10.10.10.10

16. Configure a log server.

Enable CDR log reporting, and configure the IP address of the active server to
10.10.10.20.

huawei(config-mvlan10000)#

btv

huawei(config-btv)#

igmp cdr enable

huawei(config-btv)#

quit

huawei(config)#

file-server auto-backup cdr primary 10.10.10.20 tftp

17. Save the data.

huawei(config)#

save

l

Configure the ONU.

1.

Log in to the ONU to perform the configuration.
On the OLT, use the management IP address of the ONU to log in to the ONU through
Telnet. User name:

root

(default). Password:

mduadmin

(default).

2.

Configure the traffic profile.

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,
you need to run the

traffic table ip

command to add a traffic profile.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

536

«
...
545
546
547
548
549
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Professional Series

Бренд: PACOM Страницы: 15

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: E-Lins Страницы: 113

Бренд: ebm-papst Страницы: 11

Бренд: eWON Страницы: 34

Бренд: C-Smartlink Страницы: 7

Бренд: Federal Signal Corporation Страницы: 49

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: TP-Link Страницы: 4

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренд: Extron electronics Страницы: 19

Бренд: Perle Страницы: 4

Бренд: NetComm Страницы: 75

Бренд: Proscend Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды