Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 382 / 553

background image

The total of the VLANs having been processed is 2
The total of the port VLAN(s) having been added is 2

Step 4

Add service ports to VLANs.

Create service ports for users 1, 2, 3, and 4, and then add the service ports to VLAN 100 and
VLAN 101.

huawei(config)#

service-port 1 vlan 100 vdsl mode ptm 0/1/0 multi-service user-encap

pppoe
rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 2 vlan 100 vdsl mode ptm 0/1/1 multi-service user-

encap pppoe
rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 3 vlan 101 vdsl mode ptm 0/1/2 multi-service user-encap

pppoe
rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 4 vlan 101 vdsl mode ptm 0/1/3 multi-service user-encap

pppoe
rx-cttr 6 tx-cttr 6

Step 5

Set the inner VLAN tag.

The inner VLAN tag is used to identify the user. An inner VLAN tag under the same ISP must
be unique. The VLAN tags under different ISPs can be the same with each other.

huawei(config)#

display service-port all

{ <cr>|sort-by<K>||<K> }:

Command:
display service-port all
-------------------------------------------------------------------------
INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
-------------------------------------------------------------------------
0 100 stacking vdl 0/1/ 0 - - encap pppoe 6 6 up
1 100 stacking vdl 0/1/ 1 - - encap pppoe 6 6 up
2 101 stacking vdl 0/1/ 2 - - encap pppoe 6 6 up
3 101 stacking vdl 0/1/ 3 - - encap pppoe 6 6 up
-------------------------------------------------------------------------
Total : 4 (Up/Down : 4/0)
huawei(config)#

stacking label service-port 1 11

huawei(config)#

stacking label service-port 2 12

huawei(config)#

stacking label service-port 3 11

huawei(config)#

stacking label service-port 4 12

NOTE

In the actual configuration, the index of the traffic stream may vary according to the number of traffic
streams in the system. You only need to ensure that the actual index corresponds to the inner VLAN tag.

Step 6

Save the data.

huawei(config)#

save

----End

Result

l

After being authenticated by the ISP 1 BRAS, users 1 and 2 can obtain the services provided
by ISP 1.

l

After being authenticated by the ISP 2 BRAS, users 3 and 4 can obtain the services provided
by ISP 2.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

371

«
...
380
381
382
383
384
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Lauterbach Страницы: 61

Бренд: N-Tron Страницы: 62

Бренд: Raritan Страницы: 4

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: Commell Страницы: 58

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: IBM Страницы: 34

Бренд: Conel Страницы: 32

Бренд: Kaptia Страницы: 14

Бренд: X-Micro Страницы: 49

Бренд: Airlink101 Страницы: 13

Бренд: ZyXEL Communications Страницы: 79

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

SFD-2 MkIII Jumper

Бренд: Anthem Audio Страницы: 2

Бренд: Acromag Страницы: 35

Бренд: Digital Voice Systems Страницы: 32

IP Board IPT10000C

Бренд: Dialogic Страницы: 2

Бренд: ZyXEL Communications Страницы: 348

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды