Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 236 / 553

background image

Parameter

Description

Default Setting

27

Indicates the type of remote
blocking play tone.

Numeral type. Range: 0-4.

l

0: Indicates the busy tone.

l

1: Indicates the device
congestion tone.

l

2: Indicates the mute.

l

3: Indicates the user-defined
tone 1.

l

4: Indicates the user-defined
tone 2.

Default: 0.

28

Indicates the duration of the
howler tone.

Numeral type. Range: 1-65535s.
Default: 60s

29

Indicates the duration of
message waiting tone.

Numeral type. Range: 1-60000s.
Default: 3s

30

Indicates the time limit of the
alarm for extra long call.

Numeral type. Range: 1-65535
min.
Default: 60 min.

31

Indicates whether to report the
alarm for extra long call.

Numeral type. Range: 0-1.

l

0: Indicates that the alarm is
reported.

l

1: Indicates that the alarm is
not reported.

Default: 1

32

Indicates the minimum interval
for automatic registration of the
remote block port.
The MG interface is blocked
because the MGC does not
respond or responds
incorrectly. After this
parameter is configured, the
MG interface can automatically
register with the MGC.

Numeral type. Range: 0-60000s.
0 indicates that the port does not
register automatically.
Default: 1800s

33

Indicates whether the heartbeat
message is disabled.

Numeral type:

l

0: Indicates that the heartbeat
message is disabled.

l

1: Indicates that the heartbeat
message is enabled.

Default: 1

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

225

«
...
234
235
236
237
238
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Makita Страницы: 2

Бренд: Paradyne Страницы: 16

Бренд: Aastra Страницы: 2

Бренд: Ebyte Страницы: 8

Бренд: JCG Страницы: 2

Бренд: Quantum Страницы: 20

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: WAGO Страницы: 2

Бренд: XAVI Technologies Corp. Страницы: 71

TotalStorage SAN16M-R SAN

Бренд: IBM Страницы: 116

Бренд: Cypress Semiconductor Страницы: 9

Бренд: Amplifier Tech Страницы: 36

Бренд: H3C Страницы: 26

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: hilscher Страницы: 154

Бренд: ESD Страницы: 28

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды