Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 523 / 553

background image

Service Requirements

l

Users directly uses the existing phone sets for the voice service and no additional investment
is required.

l

The voice data is carried over the IP network, which reduces the communication costs to
a great extent without compromising the communication quality.

l

Compared with traditional PSTN networks, IP-based networks provide more powerful
service functions and richer user experience.

l

The polarity-reversal accounting is supported.

Prerequisite

l

The MGC interface data and the PSTN user data corresponding to the MG interface must
be configured on the MGC.

l

Run the

display board 0

command to make sure the

Status

of the voice board of ONU is

Normal

.

Background Information

ONUs that support SIP include the MA5616, MA5603T.

An ONU support either H.248 or SIP. To query the current voice protocol on an ONU, run the

display protocol support

command. To change the voice protocol to the other one, delete the

MG interface and run the

protocol support

command. After the configuration is complete, save

it and restart the system to make the configuration take effect.

WARNING

This operation interrupts the ongoing services carried on the currently used MG interface. Hence,
exercise caution when performing this operation.

Procedure

l

Configure the OLT.

1.

Create an SVLAN and add an upstream port to it.

Create smart VLAN 200 and add upstream port 0/19/0 to it.

huawei(config)#

vlan 200 smart

huawei(config)#

port vlan 200 0/19 0

2.

(Optional) Configure upstream link aggregation.
In this example, a single upstream port is used. In the case of multiple upstream ports,
upstream link aggregation can be configured to implement protection between ports
and load sharing. For details, see

10.3 Configuring Upstream Link Aggregation

3.

Configure GPON ONU profiles.

GPON ONU profiles include the DBA profile, line profile,and alarm profile.

–

DBA profile: A DBA profile describes the GPON traffic parameters. A T-CONT
is bound to a DBA profile for dynamic bandwidth allocation, improving the
upstream bandwidth usage rate.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

512

«
...
521
522
523
524
525
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Barco Страницы: 100

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Measurement Computing Страницы: 27

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: TP-Link Страницы: 176

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

Бренд: ICP DAS USA Страницы: 31

Бренд: RR-Concepts Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды