Huawei SmartAX MA5616 Скачать руководство пользователя

Страница: 312 / 553

Table 7-30

Default configuration of the flows of the FoIP service

Item

Default

Codec negotiation mode

Negotiation

Codec mode

Transparent transmission fax

Procedure

Step 1

Configure public fax and modem parameters.
1.

Run the

interface sip

command to enter the SIP mode.

Run the

fax-modem parameters negomode

command to configure the negotiation mode.

(Optional) Run the

fax-modem parameters rtp-interval

command to enable or disable

the 10 ms packing function.

(Optional) Run the command to configure the RFC2198 function.

(Optional) Run the

fax-modem parameters vbd-codec

command to configure the codec

mode of the voice-band data (VBD).

(Optional) Run the

fax-modem parameters vbd-pt-type

command to configure the

payload type of the VBD.

(Optional) Run the

rfc2833 set rfc2833-fax-modem

command to configure the mode for

reporting fax or modem events.

Step 2

Configure the codec mode of the fax.

Run the

fax parameters

command to configure the fax working mode of the SIP interface.

Step 3

Check whether the fax transmission parameters are the same as the data plan.

Run the

display fax-modem parameters

and

display fax parameters

commands to check the

fax transmission parameters.

----End

Example

Assume that:

The negotiation mode of the MA5616 is self-switch.

The 10 ms packing function and the RFC2198 intelligent startup function are enabled.

The RFC2198 negotiation mode is fixedstart.

The codec mode of the VBD is G.711A.

The payload type of the VBD is static payload.

The transmission mode of the fax is transparent transmission (thoroughly).

To configure the MA5616, do as follows:

huawei(config)#

interface sip 0

huawei(config-if-sip-0)#

fax-modem parameters negomode self-switch rtp-interval 1

vbd-pt-type static

huawei(config-if-sip-0)#

rfc2198 set rfc2198-negomode fixedstart rfc2198-startmode

smart2198

huawei(config-if-sip-0)#

display fax-modem parameters

-------------------------------------------------------------------------------

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

301

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды

Huawei SmartAX MA5616, Руководство по настройке

Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды