manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

NOTE

l

If a matched traffic profile is not available in the system, run the 

traffic table ip

 command to configure

a new traffic profile.

l

On the MA5616, the user access rate can be limited by either a traffic profile or an ADSL line profile.
When both profiles are configured, the smaller one of the two rates configured in the profiles is adopted
as the user bandwidth. In this example, the traffic profile is used to limit the user access rate.

4.

Run the 

service-port

 command to create a service port, adopt traffic profile 5, and set the

S-VLAN ID to 50. The index of the service port is 1, and the VPI and VCI of the service
port must be the same as the management VPI and VCI of the peer modem. Assume that
the management VPI and VCI of the modem are 1 and 39, and the access port ID is
0/2/0. To facilitate the maintenance of the service port, also configure the service port
description.

huawei(config)#

service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic-

table index 5 outbound traffic-table index 5  

  

huawei(config)#

service-port desc 1 description Vlanid:50/adsl/vpi:1vci:39/

stacking

 

5.

Set the C-VLAN ID of the preset service port 1 to 10 for identifying the user. Configure
the important user packet with a higher priority so that the user packet can be processed
with precedence, and set the priority of the inner VLAN to 4.

huawei(config)#

stacking label service-port 1 10

 

huawei(config)#

stacking inner-priority service-port 1 4

Step 4

In the SHDSL access mode, follow this procedure.
1.

Configure an SHDSL profile. For details, see 

3.7.2 Configuring the SHDSL Profile

. Add

SHDSL line profile 3 of the PTM type, with the maximum line rate 2048 kbit/s.

huawei(config)#

shdsl line-profile quickadd 3 ptm rate 512 2048 

2.

Activate SHDSL port 0/4/0, and bind the preset SHDSL line profile 3 and the default
SHDSL alarm template (alarm template 1) to the port.

NOTE

By default, an SHDSL port is in the activated state. Before binding a profile or template to the port, you
must deactivate the port.

huawei(config)#

interface shl 0/4

 

huawei(config-if-shl-0/4)#

deactivate 0

huawei(config-if-shl-0/4)#

activate 0 3

huawei(config-if-shl-0/4)#

alarm-config 0 1

 

huawei(config-if-shl-0/4)#

quit

 

3.

Run the 

display traffic table

 command to query the existing traffic profiles in the system.

huawei(config)#

display traffic table ip from-index 

0  

                          

{ <cr>|to-
index<K> }:                                                           
                                                                                
  
Command:                                                                      
          display traffic table ip from-index 
0                                 
  
----------------------------------------------------------------------------  
   TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy    Pri-
Policy  
  
----------------------------------------------------------------------------  
     0      1024      34768      2048      69536   6 -              tag-
pri     
     1      2496      81872      4992     163744   6 -              tag-
pri     
     2       512      18384      1024      36768   0 -              tag-
pri     

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

324

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

ABB RELION REF615R Manual preview
RELION REF615R
Бренд: ABB Страницы: 66
Maco Standard Fitting Instructions Manual preview
Standard
Бренд: Maco Страницы: 38
Makita 3606 Parts Breakdown preview
3606
Бренд: Makita Страницы: 2
B+B SmartWorx UR5i v2 Libratum Start Manual preview
UR5i v2 Libratum
Бренд: B+B SmartWorx Страницы: 8
B+B SmartWorx ICR-1601 Start Manual preview
ICR-1601
Бренд: B+B SmartWorx Страницы: 8
Laird OL 4503 Specification And User Manual preview
OL 4503
Бренд: Laird Страницы: 36
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Pantech Sprint PX-500 Quick Start Manual preview
Sprint PX-500
Бренд: Pantech Страницы: 17
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Бренд: H3C Страницы: 54
Ublox LENA-R8 Series System Integration Manual preview
LENA-R8 Series
Бренд: Ublox Страницы: 116
H3C CR16000-M Installation Manual preview
CR16000-M
Бренд: H3C Страницы: 116
Datasheen D902AC User Manual preview
D902AC
Бренд: Datasheen Страницы: 25
Tripp Lite N48M Series Installation Manual preview
N48M Series
Бренд: Tripp Lite Страницы: 20
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Бренд: Ensemble Designs Страницы: 19
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Бренд: ICT Страницы: 34
Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B User Manual preview
ADSL 2/2+ VPN Firewall Router ADE-4300A/B
Бренд: Planet Страницы: 132
SAGEMCOM SE681 WiMAX User Manual preview
SE681 WiMAX
Бренд: SAGEMCOM Страницы: 75

Бренды по названию

Популярные бренды

Загрузить еще бренды