Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 470 / 553

background image

l

The procedure for configuring the VLAN ID extension on MA5616_B is as follows:

The configuration procedure of MA5616_B is the same as the configuration procedure of
MA5616_A. The only difference lies in the upstream VLAN ID. Hence, it is not described
here.

----End

Result

After being authenticated by the BRAS, the users on MA5616_A and MA5616_B can access
the Internet.

Two users of the MA5616 can be identified according to one outer VLAN tag. In this manner,
the number of the access user based on one VLAN tag is increased.

Configuration File

Configuration file of MA5616_A

Create a VLAN.

vlan 100 smart

Set the VLAN attribute to stacking VLAN.

vlan attrib 100 stacking

Add an uplink port to the VLAN.

port vlan 100 0/0 1

Add service ports to the VLAN.

service-port 0 vlan 100 vdsl mode ptm 0/1/2 multi-service user-encap pppoe rx-cttr
6
tx-cttr 6
service-port 1 vlan 100 vdsl mode ptm 0/1/3 multi-service user-encap pppoe rx-cttr
6
tx-cttr 6

Set the inner VLAN tag.

stacking label service-port 0 11
stacking label service-port 1 12

Configuration file of MA5616_B

Create a VLAN.

vlan 101 smart

Set the VLAN attribute to stacking VLAN.

vlan attrib 101 stacking

Add an uplink port to the VLAN.

port vlan 101 0/0 1

Add service ports to the VLAN.

service-port 0 vlan 101 vdsl mode ptm 0/1/2 multi-service user-encap pppoe rx-cttr

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

459

«
...
468
469
470
471
472
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Omnia Страницы: 102

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Garmin Страницы: 2

Бренд: IEI Technology Страницы: 187

Бренд: IEI Technology Страницы: 71

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренд: IBM Страницы: 32

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

Бренд: Delta Electronics Страницы: 1

Бренд: TRENDnet Страницы: 2

IE-SW-VL16-14TX-2SC

Бренд: Weidmuller Страницы: 17

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Бренд: iBall Baton Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды