Huawei SmartAX MA5616 Скачать руководство пользователя

Страница: 52 / 553

Configure the IP address of the gateway from the NMS server to network segment
10.50.1.0/24 to 10.10.1.1.

–

In the Solaris operating system (OS), do as follows:
Run the

route add 10.50.1.0 10.10.1.1

command to add a route.

Run the

netstat -r

command to query the information about the current routing

table.

–

In the Windows OS, do as follows:
Run the

route add 10.50.1.0 mask 255.255.255.0 10.10.1.1

command to add a

route.
Run the

route print

command to query the information about the current routing

table.

NOTE

If the IP address of the outband NMS port and the IP address of the U2000 are in the same
network segment, you need not configure the route.

Configure the SNMP parameters.

Choose

Administration

NE Communicate

Default Access Protocol

Parameters

from the main menu.

Default Access Protocol Parameters

, click the

SNMPv3 Parameters

tab,

and then click

Add

Set the profile name, and then set other parameters according to the plan.

Select corresponding protocol type in

Priv Protocol

and

Auth Protocol

, and

then click

behind the parameter. In the

Password

dialog box, set the

passwords for

Priv Protocol

and

Auth Protocol

. Then, click

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды

Huawei SmartAX MA5616, Руководство по настройке

Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды