Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 434 / 553

background image

5.

Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.

huawei(config)#

mac-address max-mac-count service-port 2 16

Step 5

In the case of the VDSL access mode, follow this procedure.

In this example, the VDSL normal mode is used as an example. For how to configure a VDSL
profile in the VDSL TI mode, see

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

1.

Configure a VDSL profile. For details, see

3.7.3.1 Configuring the VDSL2 Profile

(Normal Mode)

. Assume that the VDSL profile ID is 3, downstream rate is 2048 kbit/s,

channel mode is the interleave mode, maximum downstream interleave delay is 8 ms,
maximum upstream interleave delay is 2 ms, SNR margin is 6 dB, minimum downstream
INP is 4, and minimum upstream INP is 2.

huawei(config)#

vdsl line-profile quickadd 3 snr 60 0 300 60 0 300

huawei(config)#

vdsl channel-profile quickadd 3 path-mode atm interleaved-delay

8 2 inp 4 2 rate
128 10000 128 10000 2048 2048

huawei(config)#

vdsl line-template quickadd 3 line 3 channel1 3 100 100

2.

Activate the VDSL port. The access port is port 0/1/0, and VDSL line template 3 and the
default VDSL alarm template (alarm template 1) are bound to the port.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

huawei(config)#

interface vdsl 0/1

huawei(config-if-vdsl-0/1)#

deactivate 0

huawei(config-if-vdsl-0/1)#

activate 0 template-index 3

huawei(config-if-vdsl-0/1)#

alarm-config 0 1

huawei(config-if-vdsl-0/1)#

quit

3.

Run the

display traffic table ip

command to query the traffic profiles that exist in the

system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-
index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri
2 512 18384 1024 36768 0 - tag-
pri
3 576 20432 1152 40864 2 - tag-
pri
4 64 4048 128 8096 4 - tag-
pri
5 2048 67536 4096 135072 0 - tag-
pri
6 off off off off 0 - tag-
pri

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

423

«
...
432
433
434
435
436
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Patton electronics Страницы: 2

Бренд: Abus Страницы: 60

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: Salus Страницы: 16

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: Freescale Semiconductor Страницы: 921

Бренд: FOR-A Страницы: 39

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

HHM Series HHM2411

Бренд: TDK Страницы: 2

kontron KBox E-420-R1K/V1K

Бренд: S&T Страницы: 82

InnoMedia MTA 3328-2R

Бренд: VoiceLine Страницы: 18

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды