Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 529 / 553

background image

NOTE

l

The VLAN ID must be consistent with the CVLAN of the OLT.

l

The VLAN ID of the default upstream Ethernet port is 1. Use the default VLAN if no
specific VLAN is required for the upstream transmission.

l

If you need to use another VLAN to transmit packets in the upstream direction, run the

port vlan

command to add the specified upstream port to the VLAN.

huawei(config)#

vlan 200 smart

huawei(config)#

port vlan 200 0/0 1

//for MA5616

huawei(config)#

port vlan 200 0/9 0

//for MA5603T

huawei(config)#

interface vlanif 200

huawei(config-if-vlanif200)#

ip address 17.10.10.10 24

huawei(config-if-vlanif200)#

quit

3.

Configure the media and signaling IP address pools.
Configure both the media IP address, the signaling IP address to 17.10.10.10 and the
media gateway address to 17.10.10.1.

huawei(config)#

voip

huawei(config-voip)#

ip address media 17.10.10.10 17.10.10.1

huawei(config-voip)#

ip address signaling 17.10.10.10

huawei(config-voip)#

quit

NOTE

l

You can configure the attributes of the MG interface only when the media IP address and
the signaling IP address exist in the media and signaling IP address pools.

l

The media IP address and the signaling IP address can be different. You can plan the IP
addresses according to the actual network.

4.

Configure the static route.
Because the IP address of the VLAN interface and the IP address of the MGC are in
different network segments, you should configure a route for the network segment
from gateway 17.10.10.1 to 200.200.200.0.

huawei(config)#

ip route-static 200.200.200.0 24 17.10.10.1

5.

Add an MG interface.
Add MG interface 0.

huawei(config)#

interface h248 0

Are you sure to add MG interface?(y/n)[n]:

y

6.

Configure the attributes of the MG interface.

–

Signaling IP address: 17.10.10.10

–

Coding mode: text

–

Port number of the transport layer protocol: 2944

–

Transfer mode: UDP

–

IP address of the primary MGC: 200.200.200.200

–

Port number of the transport layer protocol of the primary MGC: 2944

–

Media IP address 1: 17.10.10.10

–

The beginning negotiation version of H248 protocol: V2

NOTE

You must confirm these as follows before configuring the MG interface.

l

The enrollment type of the MG interface: IP address or the domain name. It must be the same
strictly.

l

The beginning negotiation version of H248 protocol: V1, V2 or V3 (default). Some softswitches
do not support the V3 version, resulting in the MG interface cannot enroll.

huawei(config-if-h248-0)#

if-h248 attribute mgip 17.10.10.10 mgport

2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

518

«
...
527
528
529
530
531
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: M-Audio Страницы: 10

Бренд: GE Страницы: 93

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

EXPANSION CARD X-DANTE

Бренд: Behringer Страницы: 65

Бренд: NETGEAR Страницы: 2

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Бренд: Eicon Networks Страницы: 32

Бренд: Belkin Страницы: 2

Бренд: Moxa Technologies Страницы: 36

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: Chase Research Страницы: 114

Бренд: SilverStone Страницы: 28

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 17

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: audemat Страницы: 93

Бренд: Quatech Страницы: 5

Бренд: Gbord Страницы: 11

Бренд: WIN Enterprises Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды