Huawei SmartAX MA5616 Скачать руководство пользователя

Страница: 244 / 553

Parameter

Default Setting

Whether to support the detection of
the ANSbar signal through
monophony

Not support

Whether to support the bell ANS
signal

Not support

Power-off interval

100 ms

FSK delay interval

800 ms

Whether to enable or disable VQE
automatic gain

Disable

Whether to enable or disable VQE
noise suppression

Disable

Target value of VQE automatic gain

-22 dBm

Target value of VQE noise
suppression

12 dB

Input gain of the DSP chip

0 dB

Output gain of the DSP chip

0 dB

Name of the DSP parameter profile

- (Indicates that the DSP parameter profile is not
configured.)

FSK-mode

BELL_202

TAS-mode

NO-TAS

Procedure

Step 1

In global config mode, run the

board confirm

command to confirm the service board.

Step 2

Add a PSTN user.
1.

In global config mode, run the

esl user

command to enter the ESL user mode.

Run the

mgpstnuser add

mgpstnuser batadd

command to add a PSTN user or add

PSTN users in batches.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

233

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды

Huawei SmartAX MA5616, Руководство по настройке

Результаты поиска

Содержание SmartAX MA5616

Отзывы:

Похожие инструкции для SmartAX MA5616

Бренды по названию

Популярные бренды