manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

huawei(config-gpon-lineprofile-10)#

gem add 0 eth tcont 4

huawei(config-gpon-lineprofile-10)#

gem add 1 eth tcont 4

NOTE

a. To change the QoS mode, run the 

qos-mode

 command to configure the QoS mode to gem-

car or flow-car, and run the 

gem add

 command to configure the ID of the traffic profile

bound to the GEM port.

b. For the ONU V800R308, the QoS mode cannot be set to 

gem-car

 or 

flow-car

. To

implement QoS in the upstream and downstream directions, other modes are adopted. For
example, bind a T-CONT to a DBA profile or bind a traffic profile when creating traffic
streams.

c. When the QoS mode is PQ, the default queue priority is 0; when the QoS is 

gem-car

 or

flow-car

, traffic profile 6 is bound to the port by default (no rate limitation).

d. Before running the 

multi-service-port

 command to create service ports in batches, ensure

that the number of GEM ports is the same as the number of CVLANs. Therefore, you must
create GEM ports according to the number of CVLANs. If there are 24 CVLANs,, 24
GEM ports need to be created.

e. If you run the 

service-port

 command to create service ports one by one, note that one

GEM port can be bound to up to eight service ports. Create sufficient GEM ports according
to the number of service ports. If there are 24 CVLANs, at least three GEM ports need to
be created. This example adopts this mode and only one GEM port is created. For different
service ports within the same GEM port, you only need to replace the 

mapping-index

 and

replace the mapped VLAN with the CVLAN.

Configure the mapping between the GEM port and the ONU-side service to the
VLAN mapping mode (default), map the service port of management service
port ( the CVLAN ID is 8) to GEM port 0, and map the Internet service port (the
CVLAN ID is 1001) to GEM port 1.

huawei(config-gpon-lineprofile-10)#

mapping-mode vlan

huawei(config-gpon-lineprofile-10)#

gem mapping 0 0 vlan 8

huawei(config-gpon-lineprofile-10)#

gem mapping 1 1 vlan 1001

After the configuration is complete, run the 

commit

 command to make the

configured parameters take effect.

huawei(config-gpon-lineprofile-10)#

commit

huawei(config-gpon-lineprofile-10)#

quit

c.

(Optional) Configure an alarm profile.

–

The ID of the default GPON alarm profile is 1. The thresholds of all the alarm
parameters in the default alarm profile are 0, which indicates that no alarm is
generated.

–

In this example, the default alarm profile is used, and therefore the
configuration of the alarm profile is not required.

–

Run the 

gpon alarm-profile add

 command to configure an alarm profile,

which is used for monitoring the performance of an activated ONU line.

4.

Add an ONU on the OLT.

a.

Add an ONU.
ONU 1 and ONU 2 are connected to GPON port 0/2/1 through an optical splitter.
The IDs of ONU 1 and ONU 2 are 1 and 2 respectively. The SN of ONU 1 is
32303131B39FD641 and that of ONU 2 is 32303131B39FD642. The
management mode is SNMP and the line profile 10 is bound.
There are two ways to add an ONU. Select either of the two ways according to
actual conditions.

–

Add an ONU offline: If the password or SN of an ONU is obtained, you can
run the 

ont add

 command to add the ONU offline.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

495

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Qualys GUARD Quick Start Manual preview
GUARD
Бренд: Qualys Страницы: 2
VMIC VMICPCI-7755 Product Manual preview
VMICPCI-7755
Бренд: VMIC Страницы: 126
Intellinet 523318 Instructions preview
523318
Бренд: Intellinet Страницы: 2
Hirschmann OCTOPUS 5TX-EEC Description And Operating Instructions preview
OCTOPUS 5TX-EEC
Бренд: Hirschmann Страницы: 6
Server Technology Sentry Global Security Modem Installation And Operation Manual preview
Sentry Global Security Modem
Бренд: Server Technology Страницы: 22
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
Velopex Extra-X Quick Start Manual preview
Extra-X
Бренд: Velopex Страницы: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Бренд: Tandberg Data Страницы: 6
Juniper MX2010 Hardware Manual preview
MX2010
Бренд: Juniper Страницы: 825
OpenVox B800P User Manual preview
B800P
Бренд: OpenVox Страницы: 13
ZALMAN CNPS12X User Manual preview
CNPS12X
Бренд: ZALMAN Страницы: 11
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
NC-link NC-AP111 User Manual preview
NC-AP111
Бренд: NC-link Страницы: 20
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Бренд: Supermicro Страницы: 54
Westermo Ibex-RT-330-HV User Manual preview
Ibex-RT-330-HV
Бренд: Westermo Страницы: 34
EMTRUST CP75X User Manual preview
CP75X
Бренд: EMTRUST Страницы: 103
Network Critical SmartNA-X User Manual preview
SmartNA-X
Бренд: Network Critical Страницы: 200

Бренды по названию

Популярные бренды

Загрузить еще бренды