Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 40 / 553

background image

3.2 Configuring the U2000

The MA5616 can be interconnected with Huawei iManager U2000 (hereinafter referred to as
U2000). Hence, the administrator can maintain and manage the device through the U2000. The
MA5616 can be interconnected with the U2000 in inband or outband networking mode. The
following part describes how to configure the inband networking and outband networking based
on SNMP V1, SNMP V2c, and SNMP V3 respectively.

3.2.1 Configuring the U2000 (Based on SNMPv1)

When SNMPv1 is used, the MA5616 can be interconnected with the U2000 in inband or outband
networking mode.

Prerequisites

l

If the device is interconnected with the NMS in outband networking mode, the
communication port (maintenance network port) must be configured. For detailed
procedure, see

3.1.2 Configuring Outband Management

l

If the device is interconnected with the NMS through the PON upstream port in inband
networking mode, the communication port (PON upstream port) must be configured. For
detailed procedure, see

3.1.3 Configuring Inband Management (GPON Upstream)

.

l

If the device is interconnected with the NMS through the GE upstream port in inband
networking mode, the communication port (GE upstream port) must be configured. For
detailed procedure, see

3.1.4 Configuring Inband Management (GE Upstream)

Networking - Inband Networking Mode

As shown in

Figure 3-20

, the SNMP protocol is transmitted through the service channel. Service

packets and management packets are transmitted through the same channel. The inband NMS
management is implemented through the upstream port.

l

The MA5616 supports the GPON/GE upstream port.

l

A static route is used between the MA5616 and the U2000.

Figure 3-20

Inband networking

MA5616

U2000

OLT

BRAS

Service channel and

Management channel

Integrated NMS

Center

NMS Client B

NMS Client A

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

29

«
...
38
39
40
41
42
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Vanguard Страницы: 4

Бренд: Watchguard Страницы: 24

Бренд: Paradyne Страницы: 85

Бренд: Freund Страницы: 6

Бренд: Dataprobe Страницы: 5

SinoCon C2000-C2-SHK0401-BB1

Бренд: KonNad Страницы: 12

LMP-1202G-SFP Series

Бренд: ANTAIRA Страницы: 19

Бренд: Alarm Страницы: 5

FiberTwist G6426

Бренд: Genexis Страницы: 9

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

Бренд: Talent Страницы: 18

Бренд: iDirect Страницы: 72

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: PaloAlto Networks Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды