manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.

huawei(config)#

service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39  inbound 

traffic-table index 5 outbound
 traffic-table index 5

 

huawei(config)#

service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart 

5.

Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.

huawei(config)#

mac-address max-mac-count service-port 3 16

Step 6

Enable the IPoA-IPoE protocol conversion.
This step is to configure the IPoA MAC address pool. The start MAC address in the MAC address
pool is 0000-1111-1010, and the maximum number of the MAC addresses in the MAC address
pool is 300. The IPoA-IPoE protocol conversion is enabled, the default gateway is the same as
the IP address (192.168.1.20) of the upper-layer router, and the service encapsulation mode is
LLC-IPoA. The IP address of the modem is 192.168.1.1.

NOTE

Run the 

encapsulation

 command to configure the target IP address for IPoA encapsulation. If you do not

configure the target IP address, the IP address of the default gateway of the IPoA encapsulation is used.
This example uses the IP address of the default gateway of the IPoA encapsulation as the user target IP
address.

huawei(config)#

mac-pool xpoa 0000-1111-1010 300 

huawei(config)#

ipoa enable

huawei(config)#

ipoa default gateway 192.168.1.20

huawei(config)#

encapsulation 0/2/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1

huawei(config)#

encapsulation 0/4/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1

huawei(config)#

encapsulation 0/1/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1

Step 7

Save the data.

huawei(config)#

save

----End

Verification

l

Step 1: Set the VPI/VCI of the modem to 1/39, encapsulation mode to llc-ipoa, and IP
address to 192.168.1.1.

l

Step 2: After the settings on the modem are completed, the network connection is
automatically set up and the user can access the Internet.

l

Step 3: When downloading files through FTP, you can open 

Task Manager

 in Windows

and click 

Networking

 to check the link rate. Calculate the Internet access rate by the

formula: Attainable Internet access rate = Computer NIC rate/48 x 53 x 8. The calculated
result approximates to the planned 2048 kbit/s.

Configuration File

Configuration File of the ADSL access mode:

vlan 50 smart  
port vlan 50 0/0 0
adsl line-profile quickadd 3 2 snr 60 30 120 60 30 120
adsl channel-profile quickadd 3 interleaved-delay 10 10 rate 1024 2048 3096 1024 

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

340

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

National Instruments NI 5922 Calibration Procedure preview
NI 5922
Бренд: National Instruments Страницы: 28
National Instruments NI 9219 Getting Started preview
NI 9219
Бренд: National Instruments Страницы: 19
National Instruments NI 9219 Operating Instructions Manual preview
NI 9219
Бренд: National Instruments Страницы: 36
National Instruments NI 6711 User Manual preview
NI 6711
Бренд: National Instruments Страницы: 103
National Instruments NI PXI-1042 Series Installation Manual preview
NI PXI-1042 Series
Бренд: National Instruments Страницы: 12
National Instruments PCI-1407 Setup And Operation preview
PCI-1407
Бренд: National Instruments Страницы: 4
Konica Minolta Network Setup Network Setup Manual preview
Network Setup
Бренд: Konica Minolta Страницы: 38
Western Digital My Net N750 Start Here Manual preview
My Net N750
Бренд: Western Digital Страницы: 8
Roland MSL-15 Owner'S Manual preview
MSL-15
Бренд: Roland Страницы: 12
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Бренд: H3C Страницы: 400
Moxa Technologies ICS-G7748A Series Quick Installation Manual preview
ICS-G7748A Series
Бренд: Moxa Technologies Страницы: 10
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Бренд: Zonet Страницы: 2
Avolites Titan One Quick Start Manual preview
Titan One
Бренд: Avolites Страницы: 24
ZyXEL Communications XGS4700 Series Manual preview
XGS4700 Series
Бренд: ZyXEL Communications Страницы: 485
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Бренд: mikroElektronika Страницы: 2
Patton electronics IPLink 2803 Specifications preview
IPLink 2803
Бренд: Patton electronics Страницы: 2
Hama 00176547 Operating Instruction preview
00176547
Бренд: Hama Страницы: 25
Infoblox Infoblox-250 Installation Manual preview
Infoblox-250
Бренд: Infoblox Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды