Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 346 / 553

background image

encapsulation 0/4/0 vpi 1 vci 39 type pppoa llc
pitp enable pmode
raio-mode cntel pitp-pmode
save

Configuration File for the VDSL access mode:

vlan 50 smart
port vlan 50 0/0 0
vdsl line-profile quickadd 3 snr 60 0 300 60 0 300
vdsl channel-profile quickadd 3 path-mode atm interleaved-delay 8 2 inp 4 2 rate
128 10000 128 10000 2048 2048
interface vdsl 0/1
deactivate 0
activate 0 template-index 3
alarm-config 0 1
quit
service-port 3 vlan 50 vdsl mode atm 0/1/0 vpi 1 vci 39 inbound traffic-table index
5 outbound traffic-table index 5
service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart
mac-address max-mac-count service-port 3 16
mac-pool xpoa 0000-1111-1010 300
pppoa enable
encapsulation 0/1/0 vpi 1 vci 39 type pppoa llc
pitp enable pmode
raio-mode cntel pitp-pmode
save

8.1.4 Configuration Example of the xDSL IPoA Internet Access
Service

This topic describes how to configure a user so that the user can access the MA5616 in the xDSL
mode, and then access the Internet in the IPoA mode at a rate of 2048 kbit/s.

Service Requirements

l

The user accesses the Internet in the IPoA mode. The MA5616 works in the L2 mode.

l

User packets, which carry a single VLAN tag, are transmitted in the upstream direction,
and the services of multiple users are converged into one VLAN. This is called the N:1
access.

l

The user access rate is 2048 kbit/s, which is restricted by the traffic profile.

shows an example network of the xDSL IPoA Internet access service.

Figure 8-4

Example network of the xDSL IPoA Internet access service

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

335

«
...
344
345
346
347
348
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: Lauterbach Страницы: 61

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Бренд: Harmonic Страницы: 56

Бренд: 3Com Страницы: 18

Бренд: Supermicro Страницы: 24

Бренд: Patton electronics Страницы: 12

Supero SAS-826A

Бренд: Supero Страницы: 16

Бренд: Parker Страницы: 50

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Caton Страницы: 18

InnoMedia MTA 3328-2R

Бренд: VoiceLine Страницы: 18

iCE40 SPRAM Series

Бренд: Lattice Semiconductor Страницы: 12

Бренд: ebm-papst Страницы: 13

Бренд: Hama Страницы: 25

Бренд: Infoblox Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды