Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 355 / 553

background image

Device

Item

Data

Multicast
source

There are two multicast sources, namely, ISP 1 and ISP 2.

l

ISP 1: with IP address 10.10.10.10, providing the
multicast program with IP address 224.1.1.1

l

ISP 2: with IP address 10.10.10.11, providing the
multicast program with IP address 224.1.1.2

Program
library

Program in multicast VLAN 4002:
Program 1: with IP address 224.1.1.1 and the IP address
of the program source is the same as the IP address of ISP
1, namely, 10.10.10.10

Program in multicast VLAN 4003:
Program 2: with IP address 224.1.1.2 and the IP address
of the program source is the same as the IP address of ISP
2, namely, 10.10.10.11

Multicast user

Multicast user 1:

l

VDSL2 port: 0/1/0

l

Multicast VLAN: 4002

Multicast user 2:

l

VDSL2 port: 0/1/1

l

Multicast VLAN: 4003

Procedure

Step 1

Create VLANs and add an uplink port to the VLANs.

huawei(config)#

vlan 4002-4003 smart

huawei(config)#

port vlan 4002-4003 0/0 1

Step 2

Configure service ports.

huawei(config)#

service-port 100 vlan 4002 vdsl mode ptm 0/1/0 multi-service user-

vlan untagged
rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 101 vlan 4003 vdsl mode ptm 0/1/1 multi-service user-

vlan untagged
rx-cttr 6 tx-cttr 6

Step 3

Configure multicast VLANs and the IGMP mode.

NOTE

The IGMP mode can be configured to IGMP proxy or IGMP snooping according to the requirements. In
this example, the IGMP mode is IGMP proxy. If the planned IGMP mode is IGMP snooping, you can
configure the IGMP snooping mode by running the

igmp mode snooping

command in multicast VLAN

mode.

The IGMP mode can be switched only when the IGMP mode is off.

huawei(config)#

multicast-vlan 4002

huawei(config-mvlan4002)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

y

huawei(config-mvlan4002)#

multicast-vlan 4003

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

344

«
...
353
354
355
356
357
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

UP Squared 6000 Edge Computing Kit

Бренд: Aaeon Страницы: 59

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: Acqiris Страницы: 22

Бренд: FOR-A Страницы: 2

tBOX330-870-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Funkwerk Страницы: 2

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Teknim Страницы: 10

Бренд: Juniper Страницы: 7

Бренд: Caen Страницы: 14

Бренд: Lanner Страницы: 141

Service Aggregation Router 7705

Бренд: Alcatel-Lucent Страницы: 20

Бренд: TRENDnet Страницы: 7

Cheetah EtherCard-2320

Бренд: Accton Technology Страницы: 10

Бренд: C&H Technologies Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды