Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 176

background image

Installation

11

3.2

Incoming acceptance, transport, storage

• Make sure the packaging is undamaged!

Inform the supplier about damage to the packaging.
Keep the damaged packaging until the matter has been settled.

• Make sure the contents are undamaged!

Inform the supplier about damage to the delivery contents.
Keep the damaged goods until the matter has been settled.

• Check that the scope of delivery is complete and matches your order and the shipping documents.
• For storage and transport purposes, pack the instrument so that it is protected against impacts and

humidity. The original packaging offers the best protection. Furthermore, the permitted ambient
conditions must be observed (see "Technical data").

• If you have any questions, please contact your supplier or sales center.

3.3

Installation conditions

3.3.1

Types of mounting

You can choose from the following types of mounting for the individual components:

Device

Wall mounting

Post/pipe mounting

Panel mounting

CPG310 control unit

Mounting set included in the
scope of delivery.

not applicable

not applicable

Mycom S CPM153,
protected

Required:
2 screws Ø 6 mm (0.24")
2 wall plugs Ø 8 mm (0.31")

Mounting set included in
the scope of delivery.

Mounting set included in
the scope of delivery.

Mycom S CPM153,
outdoors

Weather protection cover
CYY102-A required if directly
exposed to weather conditions
(see Accessories).

Weather protection cover
CYY102-A and 2x round
post fixtures required (see
Accessories).

not usual

«
...
9
10
11
12
13
...
»

Содержание Topcal S CPC310

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topcal S CPC310

Бренд: 3B6 Страницы: 30

Бренд: Tascam Страницы: 4

Бренд: Harpers Страницы: 8

Бренд: Oakton Страницы: 4

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Dewetron Страницы: 24

Бренд: Environmental Express Страницы: 40

Бренд: Hanna Instruments Страницы: 28

Бренд: Eurotron Страницы: 122

WJ-NX310K Series

Бренд: i-PRO Страницы: 18

Бренд: CWT Страницы: 41

Бренд: paratronic Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды