Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 176

background image

Commissioning

82

7.6.13

Set up 2 - Controller configuration

!

Note!
The following sections describe the controller configuration of the transmitter.
Detailed information on the general functioning of controllers is provided on the CD-ROM D+
supplied.

Configuration of the transmitter

Please configure the relays of the transmitter in the following order:

1.

Type

2.

Sensor input

3.

Characteristic

In the user settings (see below), you go directly to a controller simulation and can check the settings
made and change them where necessary.

To call the menu, select:
"

Ñ

> Specialist > Set up 2 > Controller settings"

Function

Options

Info

Process

Options
• Batch 1-s. base
• Batch 1-s. acid
• Batch 2-sided
• Inline 1-s. base
• Inline 1-s. acid
• Inline 2-sided

Factory setting

Batch 1-s. base

Select the process type that describes your
process.

1-sided:

Control takes place via acid or base.

2-sided:

Control takes place via acid and base.

This function can only be selected if you defi-
ned two controllers (in the "Relays" menu
and/or via current output 2).

External hardware

Options
• Type
• Characteristic

Factory setting

Characteristic

You must configure these submenus completely
for correct operation.

Type:

Here you can select and configure the

method the controller uses to output its
manipulated variable.

Characteristic:

Here you can enter the

controller parameters (neutral zone, set point,
etc.).You also achieve "active measured value
display" via this option.

Type for "1-sided" process type

Control signal

Options
• Pulse length
• Pulse frequency
• Current output (only if

"Continuous controller" option
selected for current output 2)

Select the type of control for your process.

!

Note!

Detailed information on the types of control is
provided on the CD-ROM D+.

Pulse length

Actuator

Activation and subsequent entry
• Relay:

n.c., rel. x

• Period

001.0 ... 999.9 s

• Min. on time

000.4 ... 100.0 s

Factory setting

Relay: n.c.
Period: 010.0 s
Min. on time: 000.4 s

Select the settings for the actuator.

Relay:

Select the relay; you can choose from

the relays that you assigned to the controller in
"Set up 1 - Relays".

Period:

Period length T in seconds

Min. on time:

Minimum switch-on time;

shorter pulses are not passed on to the relay and
thus protect the actuator.

Hold

pH 7. 00

Param

[E]

¯

Process

Next

Edit[ ¯]

batch 1-s. base

batch 1-s. acid

batch 2-sided

inline 1-s. base
inline 1-s. acid

«
...
80
81
82
83
84
...
»

Содержание Topcal S CPC310

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topcal S CPC310

Бренд: Accurate Logic Страницы: 50

Acuvim-L Series

Бренд: AccuEnergy Страницы: 188

Бренд: VAMP Страницы: 78

Бренд: Oldham Страницы: 34

Бренд: OBDPROG Страницы: 8

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: UEi Страницы: 5

DIRIS Digiware D-40

Бренд: socomec Страницы: 58

Бренд: Kobold Страницы: 19

Бренд: RS PRO Страницы: 41

Бренд: Hanna Instruments Страницы: 25

Бренд: Major tech Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды