Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 98

Страница: 98 / 176

Commissioning

Edit day

Select programs

Activation and subsequent entry
• Clean

18:22 18:23

• Interval

18:24 18:54

• No prog.

Factory setting

No prog.

Select the cleaning programs for the day and
enter the times for the start of cleaning.
If you select the interval program, also enter the
time for stopping the cleaning.
The time for start and end is always shown.
Example:

Clean

18:22 (start time) 18:23 (end time)

Note!

10 program starts are possible each day.

Copy day

Select day

Options
• Tuesday
• Wednesday
• Thursday
• Friday
• Saturday
• Sunday

Factory setting

Tuesday

Select the day to which you want to copy the
day previously selected (e.g. Monday).

Note!

Danger of data loss. When copying one day to
another, the cleaning programs of the target day
are overwritten.

Interval program

Select program
Enter interval

Activation and subsequent entry
• Program

– Clean
– Clean  C
– Clean  S
– Clean  CS
– User  1
– User  2
– User  3

• Interval

0 ... 36000 s

Factory setting

Program: Clean
Interval: 3600 s

Program:

Select the program that should be

started at the defined intervals.

Interval:

Enter the time that should elapse

between the end of one program cycle and the
start of the next program cycle.

Note!

Enter an interval of at least 10 minutes here so
that the program cycles can be ended and
started correctly.

Change name

0 ... 9; A ... Z

You can enter any name for the interval
program.

Cleaning

Select program

Options
• No prog.
• Clean
• Clean  C
• Clean  CS
• Clean  S
• User prog.

Factory setting

No prog.

Select the program that should be started if the
electrode is fouled or clogged.

Power failure program

Note

The selected program is started
after a network communication
or air supply failure

Function

Options

Info

Содержание Topcal S CPC310

















































































































































































Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды

Endress+Hauser Topcal S CPC310, Руководство по эксплуатации

Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды