Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 176

background image

Commissioning

119

Absolute calibration

The transmitter has a calibrated mV display range. One absolute mV value is set with a single buffer
solution (adaptation of the measuring chain offset). A buffer solution preferably with 225 or 475 mV
is used.
Press

Ï

to start calibration.

Note

• Data saved
• Data NOT saved

(only available for digital sensors with
Memosens technology.)
Indicates whether the calibration data could be
saved in the sensor. Calibrate the sensor again if
the process of saving the data failed.

Note

Electrode in medium?

Ensure that the electrode is in the medium
again so measuring can take place.

Function

Options

Info

Note

Calibration with calibration abs.

The type of local calibration selected in the
calibration settings is displayed.

Handling instructions

Immerse:
Electrode in buffer

Immerse the electrode into the buffer.
Confirm with

F

.

buffer mV value

-1500 ... 1500 mV

Factory setting

0225 mV

Enter the buffer mV value.
Confirm with

F

.

Stability check

• Time: 10 s
• mV 1: 0

Wait until the measurement is stable:
Time no longer counts.
mV value no longer flashes.
Once these values are stable, confirm with

F

.

!

Note!

Specify the criteria for the stability check in the
"Set up 1 > Calibration > Cal settings" menu.

Calibration value notice

Invalid calibration value

This message is displayed if an error is present
(e.g. wrong buffer used).

Offset notice

Offset: 0005 mV
Good

Information on the offset and quality of the
calibration is displayed here.

Calibration

Options
• Accept
• Cancel
• Repeat calibration

Ending calibration

Accept:

When you confirm with

F

, the new

calibration data are accepted.

Cancel:

The data are not accepted. Calibration

is not repeated.

Repeat calibration:

The data are rejected and

calibration is repeated.

Sensor communication

Waiting for sensor response ...

(only available for digital sensors with
Memosens technology.)
The transmitter transmits calibration data to the
sensor.

Note

• Data saved
• Data NOT saved

(only available for digital sensors with
Memosens technology.)
Indicates whether the calibration data could be
saved in the sensor. Calibrate the sensor again if
the process of saving the data failed.

Note

Electrode in medium?

Ensure that the electrode is in the medium
again so measuring can take place.

Function

Options

Info

«
...
117
118
119
120
121
...
»

Содержание Topcal S CPC310

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Topcal S CPC310

Бренд: Saluki Страницы: 312

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

Бренд: Oldham Страницы: 96

Бренд: Bontempi Страницы: 18

Бренд: Tire-Safeguard Страницы: 6

Бренд: Sonel Страницы: 84

Бренд: JUMO Страницы: 150

Бренд: Elcontrol Страницы: 7

Бренд: Chauvin Arnoux Страницы: 64

1101-3121-0049-800

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Camlab Страницы: 28

Бренд: Hanna Instruments Страницы: 28

Бренд: UEi Страницы: 16

Бренд: THORLABS Страницы: 20

BAE LX-XO-PL018-L S4 Series

Бренд: Balluff Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды