Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 109

Страница: 109 / 176

Commissioning

109

7.8

Diagnosis

To call the menu, press

Function

Options

Info

Diagnosis

Options
• Error list
• Error log
• Operation log
• Calibration log
• Validate log
• Ext. sensor data (only for

digital sensors with
Memosens technology)

• Service

Error list:

Displays the error currently active.

(Complete error list with description, see the
"Troubleshooting" section).

Error log:

Lists the 30 errors last reported with

date and time.

Operation log:

Lists the 30 operating steps last

registered with date and time.

Calibration log:

Lists the last 30 calibrations

performed with date and time.

Validate log:

Lists the last 30 Topcal validati-

ons.

Ext. sensor data:

Lists the data saved in the

sensor, e.g. sensor identification, calibration
data, hours of operation etc.

Note!

• Use the arrow keys to scroll through the lists.
• Exit the lists with

Calibration log

Calibration data

• 1 data input
• Zero point
• Slope
• El. condition
• <Date> <time>

1 data input

Displays the calibration method

used.

Zeropoint:

Displays the zero point calculated

during calibration.

Slope:

Displays the slope calculated during

calibration.

Electr. condition:

Displays the electrode con-

dition.

<Date> <time>:

Displays the date and time of

the calibration.

If you are using a digital sensor with Memosens functionality, you get the following information after pressing

• SNR
• Sensor change date
• <Date> <time>

Displays the serial number of the calibrated
sensor and the date and time of the sensor
change.

Ext. sensor data (only for sensors with Memosens technology)

The transmitter indicates that the sensor data are being read out. The display automatically switches on completion of the
read-out process.
If the system does not automatically continue, you can call up the data last read out by pressing

or return to

measuring operation by pressing

Data of the digital sensor

Options
• Identification
• Calibration data
• Comp. temperature
• Sensor status
• Sensor info

Select the data saved in the digital sensor which
are to be displayed.

Identification

Manufacturer data

• ID
• SW  ID
• HW  version
• SW  version

ID:

Displays the module ID of the sensor.

SW ID:

Displays the software ID of the sensor.

HW version:

Displays the hardware version of

the digital sensor.

SW version:

Displays the software version of

the digital sensor.

• Check date
• SAP
• SN

Check date:

Indicates when the factory test of

the sensor was carried out.

SAP:

Displays the SAP number of the sensor.

SN:

Displays the serial number of the sensor

electronics.

pH 7.00

Hold

Diag

Select

Error list

Error log
Operation log

Calibration log

Service

Edit [¯]

Next [E]

Содержание Topcal S CPC310

















































































































































































Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды

Endress+Hauser Topcal S CPC310, Руководство по эксплуатации

Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды