Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 103

Страница: 103 / 176

Commissioning

103

Edit line

Options
• Change
• Delete
• Move to
• Insert

Select the editing function for the selected line.

Edit:

The function for the selected item is

changed, e.g. "Water" changed to
"W.+Cleaner".

Delete:

The selected function is deleted (you

are not asked to confirm you really want to
delete)

Move to:

The selected function is moved to

another position.

Insert:

A new item is inserted ahead of the

selected item.

Setup

Adjusting program steps

Options
• Water 0 s
• W.+clean. 0 s

...

Select the program step you want to adjust.

Enter values

0 ... 9999 s
0x
(depending on the selected
program step)

Enter the desired value for the selected program
step.

Cleaner / Water:

Specify the time as to how

long the cleaner/water should be pumped.

Wait:

Enter the time as to how long the system

should remain in its current state.

Back to:

Enter the number of repeats a loop

should run through.

Program time

Prog.time

0 ... 9999 s

The total duration of the selected program is
displayed here. The display cannot be edited.

Rename

Change name

0 ... 9; A ... Z

Enter a new name for the user program.

Automatic

Select day

Options
• Monday
• Wednesday
• Thursday
• Friday
• Saturday
• Sunday

Factory setting

Monday

Select the day you want to edit.

Select the editing function for the
day

Options
• Edit day
• Copy day

Factory setting

Edit day

Edit day:

You edit the cleaning cycle for the

selected day.

Copy day:

The day selected in the previous

field is copied to the day you select in the
following field.

Edit day

Select programs

Activation and subsequent entry
• No prog.
• Clean

18:22 18:23

• Interval

18:24 18:54

Factory setting

No prog.

Select the cleaning programs for the day and
enter the times for the start of cleaning.
If you are using the interval program, also enter
the time for stopping the cleaning.
The time for start and end is always shown.
Example:

Clean

18:22 (start time) 18:23 (end time)

Function

Options

Info

Содержание Topcal S CPC310

















































































































































































Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды

Endress+Hauser Topcal S CPC310, Руководство по эксплуатации

Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды