Endress+Hauser Topcal S CPC310 Скачать руководство пользователя страница 84

Страница: 84 / 176

Commissioning

2 outputs

Control type

Activation and subsequent entry
• Acid

– Pulse length
– Pulse frequency

• Base

– Pulse length
– Pulse frequency

Factory setting

Acid: Pulse length
Base: Pulse length

Select the type of control for your process.

Note!

Detailed information on the types of control is
provided on the CD-ROM D+.

For acid/base dosing in each
case:
Actuator (only for pulse
length)

Activation and subsequent entry
• Relay:

n.c., rel. x

• Period

001.0 ... 999.9 s

• Min. on time

000.4 ... 100.0 s

Factory setting

Relay: n.c.
Period: 010.0 s
Min. on time: 000.4 s

Select the settings for the actuator.

Relay:

Select the relay; you can choose from

the relays that you assigned to the controller in
"Set up 1 - Relays".

Period:

Period length T in seconds

Min. on time:

Minimum switch-on time;

shorter pulses are not passed on to the relay and
thus protect the actuator.

For acid/base dosing in each
case:
Actuator (only for pulse
frequency)

Activation and subsequent entry
• Relay:

n.c., rel. x

• Max. frequency

060 ... 120 min

-1

Factory setting

Relay: n.c.
Max. frequency: 120 min

-1

Select the settings for the actuator.

Relay:

Select the relay; you can choose from

the relays that you assigned to the controller in
"Set up 1 - Relays".

Max. pulse frequency:

Enter the maximum

pulse frequency; pulses with a higher frequency
are not passed on to the relay.

Characteristic

Characteristic type

Options
• Linear
• Segmented

Select the characteristic type.

Linear characteristic

Corresponds to a

constant control gain.

Segmented characteristic

Corresponds to a

range-dependent control gain.

Linear curve

characteristic values

Activation and subsequent entry
• Start neutral zone

-2.00 ... 7.00 pH

• End neutral zone

7.00 ... 16.00 pH

• Control point

-2.00 ... 16.00 pH (depends
on start neutral and end
neutral zone)

• K

00.00 ... 99.99

• K

00.00 ... 99.99

Factory setting

Start neutral zone: 6.50 pH
End neutral zone: 7.50 pH
Control point: 7.00 pH
K

1: 01.00

2: 01.00

Select the settings for linear control gain.

Control point:

The value that is to be set.

Start neutral zone:

Start neutral zone

End neutral zone:

End neutral zone

(only for base dosing): Gain for base

dosing

(only for acid dosing): Gain for acid dosing

Function

Options

Info

Содержание Topcal S CPC310

















































































































































































Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды

Endress+Hauser Topcal S CPC310, Руководство по эксплуатации

Результаты поиска

Содержание Topcal S CPC310

Отзывы:

Похожие инструкции для Topcal S CPC310

Бренды по названию

Популярные бренды