CTC Union GSW-3208M Скачать руководство пользователя страница 32

Страница: 32 / 148

Chapter 6. Manage / Configure the Switch

dot1x dynamic-vlan

command is used to enable Dynamic VLAN function for 802.1x operation. If it is enabled, the

switch will assign the user to the VLAN assigned from RADIUS server. And

dot1x dynamic-vlan

command can

be used to disable it.

dot1x guest-vlan x

command is used to enable and select the VLAN for users fail to authenticated by RADIUS server.

“x” is the VLAN ID. And

dot1x guest-vlan

command can be used to disable it.

dot1x max-req x

command is used to set max request timeout count between the switch and RADIUS server before

authentication fail. The valid value of “

” is 1~10.

dot1x re-authentication

command is used to force re-authentication on all ports.

dot1x system-auth-control

command is used to enable 802.1x function on the switch. And

dot1x system-auth-

control

command can be used to disable it.

dot1x timeout ...

command is used to setup timeout values in 802.1x operation. Entering “dot1x timeout ?”, the sub-

command will be shown.

(config)# dot1x timeout ?

quiet-period Time after Max Request Count before gets new client

re-authperiod Time after connected client must be re-authenticated

server-period Time after an authenticator sends a RADIUS Access-Request packet to the authentication server

supplicant-period Time after an authenticator sends an EAP-Request/ MD5 Challenge frame to a supplicant

tx-period Time switch waits before re-transmitting EAP packet

dot1x timeout quiet-period x

command is used to set the quiet time value between the switch and the user before

next authentication process when authentication fail. The valid value of “

” is 0~65535.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды