CTC Union GSW-3208M Скачать руководство пользователя страница 28

Страница: 28 / 148

Chapter 6. Manage / Configure the Switch

6.2.3 Configure Mode Commands

Entering “

configure

” command at console interface, the prompt will become ...

“(configure)#”.

All the general settings for the switch can be done in this mode.

If the settings are for ports, it is done with “interface” command in configure mode. For example, “interface ethernet

1/5” is for settings on Port 5 and “interface ethernet 1/5,6,10-15” is for settings on Port 5, 6, 10, 11, 12, 13, 14, 15.

Please refer to next section for the details of this command.

Enter “?” at the prompt, the sub-command list will be shown.

------------------------------------------------------------------------------

------

(config)# ?

exit Exit from current mode

help Show available commands

history Show a list of previously run commands

logout Disconnect

quit Quit commands

automode Set Auto Negotiation or Auto Detect mode

default Restore to factory default setting

dhcp-relay DHCP relay setting

dot1x Configures 802.1x port-based access control

end Exit from configure mode

hostname Sets system's network name

interface Enters privileged interface configuration

ip Global IP configuration sub commands

ip-filter

Enable IP address filtering function

lacp Configures LACP status

logging Modifies message logging facilities

mac-address-table Configuration of the address table

management Specifies management IP filter

mirror Configuration of mirror

mvr Multicast VLAN Registration

no Negates a command or sets its defaults

prompt Sets system's prompt

qos Configuration of QoS

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды