CTC Union GSW-3208M Скачать руководство пользователя страница 137

Страница: 137 / 148

Chapter 6. Manage / Configure the Switch

137

6.4.12 Tools

The follow functions are used for system maintenance. They are Software Upgrade, Configuration Backup/Restore,

Restore Factory Default, Reset System, and Ping functions.

1). Tools Information

Four functions are supported as the system maintenance tools.

System Upgrade

: This function will upgrade the system operation software from the web management PC.

Config Backup/Restore

[Backup Setting]

: Clicking this button, the switch will backup the configuration of the switch to the web management

PC.

[Backup Setting to text file]

: Clicking this button, the switch will backup the configuration of the switch to the web

management PC in text format.

[Restore Setting]

: The configuration of the switch can be restored to switch by clicking this button after the

configuration file is selected.

Restore Factory Default

: This function will restore the switch configuration to factory default setting.

Reset System

: This function will cause the switch to reboot itself.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды