CTC Union GSW-3208M Скачать руководство пользователя страница 35

Страница: 35 / 148

Chapter 6. Manage / Configure the Switch

ip default-gateway x.x.x.x

command is used to specify the default gateway for IP configuration of the switch.

x.x.x.x is the IP address of the gateway device.

ip http ...

command is used to configure http service of the switch.

Entering “ip http ?”, the sub-command will be shown.

(config)# ip http ?

secure-server Enable secure HTTP server

server Enable HTTP server

ip http secure-server

command is used to enable the SSL function of http service (https) of the switch. And

http secure-server

command can be used to disable it.

ip http server

command is used to enable http service of the switch. And

no ip http server

command can be used

to disable it.

Because hacker or worm/virus (like ColdRed) often attacks http server, this command is provided to enable/disable

http service to prevent it. (If this switch is installed in public Internet without any firewall protection, we suggest

users to disable the http interface and use Telnet or SNMP instead.)

ip igmp ...

command is used to configure IGMP operation of the switch. Entering “ip igmp snooping ?”, the sub-

command will be shown.

(config)# ip igmp snooping ?

mrouter Multicast router

query Enable IGMP query function

query-interval Configures query interval

query-max-response-time Configures the report delay

router-port-expire-time Configures router port expire time

unregflood Enable IGMP unregister flood function

<cr>

ip igmp

command is used to enable IGMP function of the switch. And

no ip igmp

command can be used to disable

it.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды