CTC Union GSW-3208M Скачать руководство пользователя страница 126

Страница: 126 / 148

Chapter 6. Manage / Configure the Switch

126

Seven DSCP values (0~63) could be defined and map to priority queue at “IP Differential Service (DiffServ)

Configuration” page by clicking [Configure DSCP Priority] button.

[Configure VLAN Tag Priority]

button : Click this button can go to the “VLAN Tag Priority” page for 802.1P priority

values (0~7) to priority queue mapping setting.

[Configure DSCP Priority]

button : Click this button can go to the “IP Differential Service (DiffServ) Configuration”

page for DSCP priority values (0~63) to priority queue mapping setting.

[802.1P Priority Mapping]

For 802.1P priority, priority value (0~7) in VLAN tag will be used for QoS operation. And the mapping of priority

values to priority queues (High/Middle /Normal/Low) could be defined here.

This mapping is done by port. And “All” could be selected for every port.

If 802.1P priority function is enabled, these settings will be followed for QoS operation.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды