CTC Union GSW-3208M Скачать руководство пользователя страница 129

Страница: 129 / 148

Chapter 6. Manage / Configure the Switch

129

6.4.9 IGMP

This switch supports IGMP Snooping function for IP Multicast traffic. Switch will learn IP Multicast Groups from

IGMP protocol packets. Here is for IGMP function configuration settings.

1). IGMP Configuration

IGMP Status

: this is used to enable/disable IGMP function.

IGMP Querying

: this is used to enable/disable IGMP Query function. This switch will send IGMP Query at a fixed

interval if it is enable. The IGMP query responses, known as IGMP reports (which look very much like an IGMP join)

keep the switch updated with the current multicast group membership on a port-by-port basis.

Unregistered IPMC Flooding

: unregistered (un-joined) IP multicast traffic will be flooded to every port if this setting

is enable. If it is disable, the unregistered IP multicast traffic will be flooded to IP multicast members only

IGMP Query Interval

: this is used to set the IGMP query packet sending interval if IGMP Query function is enable.

IGMP Report Delay

: this is used to set the delay time to send report after receiving a query. When a host receives a

Query, it doesn’t send a report immediately but it starts a report delay timer for each group membership on the network

interface of the incoming Query. When the timer expires, a report is generated for the corresponding host group.

IGMP Query Timeout

: this is used to set the timeout interval for IGMP Query operation. If the switch does not

receive updated membership information in a timely fashion, it will stop forwarding multicasts to the delinquent port

where the end-device is located.

[Router Port]

This is used to select the port that connected to IGMP active router.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды