CTC Union GSW-3208M Скачать руководство пользователя страница 40

Страница: 40 / 148

Chapter 6. Manage / Configure the Switch

mvr x active

command is used to set the MVR VLAN to “active” state. “

” is the MVR VLAN ID. “

no mvr x

active

” command is used to set the MVR VLAN to “inactive” state.

mvr x group yyy start-address m.m.m.m end-address n.n.n.n

command is used to create a IP multicast group for

the MVR VLAN. After MVR VLAN is created, you can assign IP multicast groups (video channels) to the MVR

VLAN. And you can assign more than one IP multicast groups (video channels) to one MVR VLAN. “

” is the

MVR VLAN ID. “

yyy

” is the name of the IP multicast group. “

m.m.m.m

” is the start IP multicast address.

“

n.n.n.n

” is the end IP multicast address. For example, “mvr 10 group abc start-address 224.0.0.1 end-address

224.0.0.2”. “

no mvr x group yyy

” command is used to delete the IP multicast group named “yyy” from MVR VLAN

“x”.

mvr x mode compatible

mvr x mode dynamic

command is used to set the operation mode of the MVR VLAN.

There are two operation modes for this MVR function. One is Dynamic mode. Another is Compatible mode. In

Dynamic mode, the switch will send IGMP reports to every MVR source port in the MVR VLAN. In Compatible

mode, the switch will not send IGMP reports. “

” is the MVR VLAN ID.

mvr x name yyy

command is used to assign a name to the MVR VLAN. “

” is the MVR VLAN ID. “

yyy

” is the

name string.

After MVR VLAN is created, source port of IP multicast traffic and receiver ports of subscribers will be assigned next.

Assigning source port and receiver port to MVR VLAN is done in “(config-if)#” mode (go with “interface ethernet

1/x” command. “x” is the port number.) Please refer to “mvr” command in Section 6.2.4.1 for the details.

command

This command is used to disable a function or restore a setting to factory default of the switch.

(config)# no ?

automode Set Auto Negotiation or Auto Detect mode

dhcp-relay Set Auto Negotiation or Auto Detect mode

dot1x Configures 802.1x port-based access control

hostname Sets system's network name

ip Global IP configuration sub commands

ip-filter Enable IP address filtering function

lacp Configures LACP status

logging Modifies message logging facilities

mac-address-table Configuration of the address table

management Specifies management IP filter

mirror Configuration of mirror

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды