CTC Union GSW-3208M Скачать руководство пользователя страница 72

Страница: 72 / 148

Chapter 6. Manage / Configure the Switch

show interface

command

This command is used to show port information and status.

# show interface ?

counters Interface counters information

status Interface status information

switchport Interface switchport information

show interface counters

command will show total statistics counters for all ports.

show interface counters ethernet 1/x

command will show statistics counters for Port x. (“

” is the port number).

For example,

# show interface counters ethernet 1/3

Port: 1/3

==========================================

Rx Counter Statistics

Good Unicast Frame 4109

Good Broadcast Frame 9946

Good Multicast Frame 158

Discarded Frame 0

Errors 0

Total Receive Byte Count 1549816

==========================================

Tx Counter Statistics

Good Unicast Frame 2001

Good Broadcast Frame 18

Good Multicast Frame 0

Discarded Frame 0

Errors 0

Total Transmit Byte Count 873047

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды