CTC Union GSW-3208M Скачать руководство пользователя страница 64

Страница: 64 / 148

Chapter 6. Manage / Configure the Switch

ip address dhcp

command is used to enable DHCP client function. DHCP client function will try to get IP

configuration from DHCP server in network. And

no ip address dhcp

command can be used to disable it.

ip address x.x.x.x y.y.y.y

command is used to set IP address of the switch on this VLAN. “

x.x.x.x

” is the IP address.

“

y.y.y.y

” is the subnet mask.

For example, “ip address 192.168.1.12 255.255.255.0” will set the IP address of the switch on this VLAN group for

remote management.

ip address renew

command is used to refresh the lease time of the IP address got by DHCP. If IP configuration is

not got when boot-up, this command will try to get IP configuration again.

ip address release

command is used to release current IP address got by DHCP. Then, you can try to get the IP

configuration again by “ip address renew” command.

command

This command is used to disable a function or restore a setting to factory default of the switch.

(config-if)# no ?

ip Internet protocol

For example,

“

ip address dhcp

” command can enable DHCP client function on the VLAN group interface and “

no ip address

dhcp

” command can disable it.

6.2.5 VLAN Configuring Commands

Commands in Configuring Mode are for general switch settings. And its prompt is “(config)#”.

If the settings are for VLANs, it should enter VLAN configuring mode first by “

vlan database

” command in configure

mode. And its prompt will become “

(config-vlan)#

”.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды