CTC Union GSW-3208M Скачать руководство пользователя страница 75

Страница: 75 / 148

Chapter 6. Manage / Configure the Switch

# show ip igmp snooping mrouter

Type M'cast Router Ports

------ --------------------

--------------------------------

static Eth 1/

show ip interface

command will show current switch IP configuration.

For example,

# show ip interface

IP address and netmask: 192.168.1.12 255.255.255.0 on VLAN 1

show ip redirects

command will show current IP gateway setting of the switch.

For example,

# show ip redirects

gateway: 192.168.1.254

show ip-filter

command

This command is used to show current IP-Filter function status of the switch.

# show ip-filter

IP Filter Configuration

IP Address Filter: Disable

For showing filter IP address, “show interface switchport” command will show port settings one after another. And

“show interface switchport ethernet 1/x” command will show Port x settings.

show lacp

command

This command is used to show current LACP configuration of the switch.

# show lacp ?

internal Shows config settings/operational state for local side

portstatus Shows LACP Port Status

sysid Shows channel groups system priority/MAC address

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды