CTC Union GSW-3208M Скачать руководство пользователя страница 108

Страница: 108 / 148

Chapter 6. Manage / Configure the Switch

108

Mode

: This is used to enable/disable Mirror function.

Monitering Port

: This is used to set the capture port. The switch will copy the traffic from Monitored Port to this port

if Mirror function is enabled.

Monitored Port

: This is the monitored port. The switch will copy the traffic from this port to Monitoring Port.

5). Rate Control

Two traffic rates could be controlled by the switch. One is the ingress/egress traffic of each port. Another is

Broadcast/Multicast/Unicast Storm Control.

5-1) Rate Control Configuration

This function can setup the ingress and egress rate limit of ports.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды