CTC Union GSW-3208M Скачать руководство пользователя страница 125

Страница: 125 / 148

Chapter 6. Manage / Configure the Switch

125

6.4.8 QoS

This switch supports Port-based priority, 802.1P priority, and DSCP priority. These priority operations could be

enable/disable on each port.

For 802.1P and DSCP priority operations, their priority values can be mapped to four priority queues on each port of the

switch for QoS operation.

1). QoS Information

QoS

: this is for QoS function enable/disable.

Port Priority

: this is used to define the priority setting of each port. It will map to the four priority queues of the

switch.

802.1P Enable

: this is for 802.1P priority operation enable/diable on each port. 802.1P priority operation will use the

priority setting in tag of packets for QoS operation.

The mapping of 802.1P priority values (0~7) to priority queue could be defined at “VLAN Tag Priority” page by

clicking [Configure VLAN Tag Priority] button.

DSCP Enable

: this is for DSCP(Differential Service Code Point) priority operation enable/disable on each port. DSCP

priority operation will use the priority setting in ToS field of IP packets for QoS operation.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды