CTC Union GSW-3208M Скачать руководство пользователя страница 139

Страница: 139 / 148

Chapter 7. Software Update and Backup

139

Chapter 7. Software Update and Backup

This switch supports software update and configuration backup/update/restore functions. It could be done in two ways.

From console when booting

: by Xmodem protocol and doing by terminal program. This function can be used for

run-time code and boot code updating. (Boot code works only at boot time - before the main program starts.)

Press Ctrl-C when the switch is booting, the following message will be shown.

Boot Menu

===========================

0: Start the Run-time code

1: Upgrade Run-time code

2: Upgrade Boot Code

=> Select:

Start Run-time code

: This option will continue the booting process.

Upgrade Run-time code

: This option will try to update run-time code (main code) from terminal program with

Xmodem protocol. If this option is selected, the following message will be shown.

“Waiting to receive file by Xmodem ....”

Then user can select “Send File” function of terminal program and select Xmodem protocol and the update file,

then start the file upgrade.

Upgrade Boot Code

: This option will try to update boot code from terminal program with Xmodem protocol. User

can select “Send File” function of terminal program and select Xmodem protocol and the update file, then start the

file upgrade.

From web browser

: Doing by http protocol and by web browser. Please refer to the description of “

Tools

” function

in Section 6.4.12.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды