CTC Union GSW-3208M Скачать руководство пользователя страница 45

Страница: 45 / 148

Chapter 6. Manage / Configure the Switch

spanning-tree max-age x

command is used to set the spanning tree aging time if no spanning tree maintenance

packet is received. “

” is the time, and its valid value is 6-40 in seconds.

spanning-tree priority x

command is used to set the bridge priority of the switch. Bridge priority is for selecting the

root device, root port, and designated port. The device with the highest priority (lowest value) becomes the STA root

device. If all devices have the same priority, the device with the lowest MAC address will then become the root

device. “

” is the priority, and its valid value is 0-61440.

The settings of spanning tree on port are done in “interface” command. The settings here are for bridge only.

storm-control

command

This command is used to set the storm control rate. The packet storms that could be controlled are broadcast,

multicast, and unicast flooding traffic. And the rate is counted with packet per second(pps), not bit per second(bps).

storm-control bc-rate x

command is used to set rate limit for broadcast traffic. “

” is the limit rate number, and its

valid value is 0-7. (0:disable, 1:1Kpps, 2:2Kpps, 3:4Kpps, 4:8Kpps, 5:16Kpps, 6:32Kpps, 7:64Kpps)

storm-control mc-rate x

command is used to set rate limit for multicast traffic. “

” is the limit rate number, and its

valid value is 0-7. (0:disable, 1:1Kpps, 2:2Kpps, 3:4Kpps, 4:8Kpps, 5:16Kpps, 6:32Kpps, 7:64Kpps)

storm-control fc-rate x

command is used to set rate limit for unicast flooding traffic. “

” is the limit rate number,

and its valid value is 0-7. (0:disable, 1:1Kpps, 2:2Kpps, 3:4Kpps, 4:8Kpps, 5:16Kpps, 6:32Kpps, 7:64Kpps)

trunk

command

This command is used to enable trunk function of the switch. And

no trunk

comand can be used to disable it.

The trunk function for the switch works with LACP protocol. The system priority of LACP is set by “lacp”

command. And the settings on ports is done in “interface” command.

username

command

This command is used to set the username and password for administrator and guest.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды