CTC Union GSW-3208M Скачать руководство пользователя страница 105

Страница: 105 / 148

Chapter 6. Manage / Configure the Switch

105

6.4.4 Port

This section is about configurations for ports. For port speed setting, maximum packet size setting, mirror port setting,

port bandwidth limit, and port statistics.

1). Port Configuration

This function is used to configure port settings of the switch. You can enable /disable a port, set it to fixed 10M or

100M or 1000M ... and so on.

Auto Mode

: User can select the operation mode of port when “auto” is set to disabled.

For “Auto Negotiation” mode, the switch will do port auto-negotiation function ON/OFF when the auto function of port

(in Port Configuration setting) is enabled/disabled.

For “Auto Detect” mode, the switch will always keep port auto-negotiation function ON but just modify its attribution if

auto function of port (in Port Configuration setting) is disabled.

For applications, you should select “Auto Detect

”

mode if the connected device is auto-negotiation enabled. (For

example, customer’s PC is auto-negotiation enable and you want to set his network connection to work at 10Mbps.)

And you can select “Auto Negotiation

”

mode if the connected device is auto-negotiation disabled (it is called forced

mode, sometimes). Some of old TX-FX Converters needs to work in this mode because FX supports 100/Full forced

mode only.

For most applications, “Auto Detect” mode is OK.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды