CTC Union GSW-3208M Скачать руководство пользователя страница 67

Страница: 67 / 148

Chapter 6. Manage / Configure the Switch

command

This command is used to disable a function or restore a setting to factory default of the switch.

(config-vlan)# no ?

1q-vlan Configures 802.1Q VLAN

port-vlan Configures Port-Based VLAN

private-vlan Private VLAN

vlan Switch Virtual LAN interface

For example,

“

1q-vlan

” command can enable 802.1Q VLAN function and “

no 1q-vlan

” command can disable it. “

no vlan 100

”

command will remove VLAN 100.

port-vlan

command

This command is used to enable Port-base VLAN. And 802.1Q VLAN function will be disable at the same time.

port-vlan

command is used to enable Port-base VLAN.

no port-vlan

command is used to disable it.

private-vlan

command

This command is used to create VLAN groups for Private VLAN and create the associations between Primary VLAN

and Community VLAN.

(config-vlan)# private-vlan 100 ?

association Association

name VLAN interface name

private-vlan x association y

command is used to create the association between Primary VLAN “

” and Community

VLAN “

”

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды