CTC Union GSW-3208M Скачать руководство пользователя страница 61

Страница: 61 / 148

Chapter 6. Manage / Configure the Switch

[ Private VLAN Port Assignment ]

switchport private-vlan host-association x

command is used to assign this interface port(s) to a Community VLAN.

And the port type of the interface port(s) must be “host” first. “

” is the VLAN ID of the Community VLAN and its

valid value is 2~4094.

switchport private-vlan isolated x

command is used to assign this interface port(s) to a Isolated VLAN. And the

port type of the interface port(s) must be “host” or “promiscuous” first. “

” is the VLAN ID of the Isolated VLAN

and its valid value is 2~4094.

switchport private-vlan mapping x

command is used to assign this interface port(s) to a Primary VLAN. And the

port type of the interface port(s) must be “promiscuous” first. “

” is the VLAN ID of the Primary VLAN and its

valid value is 2~4094.

[ VLAN Stacking (Q-in-Q) Setting ]

switchport vlan-stacking normal

command is used to set the port(s) as normal 802.1Q VLAN port(s).

And the

tagged/untagged setting will follow the settings in 802.1Q VLAN.

switchport vlan-stacking access

command is used to set the port(s) as access port(s) for VLAN stacking operation.

will strip a tag from tagged or double-tagged packets before forwarding. It is for downward connection of VLAN stacking

operation.

switchport vlan-stacking tunnel

command is used to set the port as tunnel port for VLAN stacking operation.

It will

add a tag and allow two 802.1Q VLAN tags in a packet. It is for tunnel and upward connection of VLAN stacking operation.

6.2.4.2 Interface Configuring Commands for VLAN

Commands in Configuring Mode are for general switch settings. And its prompt is “(config)#”.

If the characteristics are for VLAN group, it is done with “

interface vlan x

” command in configure mode. For

example, “interface vlan 100” is for characteristics settings on VLAN 100.

Note:

The general VLAN settings are done with “

vlan database

” command. Please refer to section

6.2.5 VLAN

Configuring Commands

for the details. And

interface vlan x

command is used to assign characteristics to a VLAN

group interface. For example, assigning IP address to a VLAN interface is done with this command.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды