CTC Union GSW-3208M Скачать руководство пользователя страница 25

Страница: 25 / 148

Chapter 6. Manage / Configure the Switch

show

command

This command is used to show current system information and system configuration.

Enter “show ?” at the prompt, the sub-command list will be shown.

# show ?

calendar Date and time information

dhcp-relay DHCP Relay Configuration

dot1x 802.1x content

gvrp GVRP configuration

history History information

interface Interface information

ip IP information

ip-filter IP Filter Configuration

lacp LACP statistics

line TTY line information

log Log records

mac-address-table Configuration of the address table

mac-security MAC Security Configuration

management Management IP filter

map Maps priority

mvr Show MVR Status

port Port characteristics

queue Priority queue information

radius-server RADIUS server information

running-config Information on the running configuration

rate-limit Configures rate-limits

snmp Simple Network Management Protocol statistis

sntp Simple Network Time Protocol configuration

spanning-tree Spanning-tree configuration

system System information

trunk Trunk information

version System hardware and software versions

vlan Virtual LAN settings

With sub-commands, different configuration settings will be displayed.

More help information for them will be prompted with “show xxxx ?” (xxxx is the sub-command). For example,

entering “show ip ?” will get the prompt message...

# show ip ?

igmp IGMP snooping

interface Interface information

redirects Default gateway configured for this device

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды