CTC Union GSW-3208M Скачать руководство пользователя страница 106

Страница: 106 / 148

Chapter 6. Manage / Configure the Switch

106

Port Setting

: It is for modifying the setting of port. Follow the steps to do it.

Select the port that you want to modify in “Port#” first.

Fill the name of the port.

Select Enable/Disable state in “Admin”. If Disable is selected, this port will be disabled for any network access.

Select the Enable/Disable state of Auto function of port. The auto mode could be auto-negotiation or auto-detect

operation when auto is set to disable.

If Auto is disabled, select the operation speed and duplex mode of the port in “Speed/Duplex”.

Select the Enable/Disable state of Flow Control function of port.

Select the Enable/Disable state of Power Saving function of port. If it is enabled, port will go to low power state

when link down.

Select MDI/MDI-X operation mode. It could be “Auto”, “MDI”, or “MDI-X”. “Auto” can auto-detect and get the

correct connection mode. “MDI” will set the port to MDI mode for switch-to-switch connection. “MDI-X” will

set the port to MDI-X mode for user PC connection.

Click [Apply] after any modification.

2). Port Information

Current Setting & Link Status

: It is current status of ports.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды