CTC Union GSW-3208M Скачать руководство пользователя страница 63

Страница: 63 / 148

Chapter 6. Manage / Configure the Switch

quit

command

This command is used to quit from console interface. It has the same function as logout.

interface

command

This command is used to change to interface port(s) or another interface VLAN groups for next setup commands.

(config-if)# interface ?

ethernet Ethernet port

vlan Switch Virtual LAN interface

For example,

“(config)# interface ethernet 1/5” will change the setup interface to Port 5 and all the following commands will be

applied to Port 5.

“(config-if)# interface ethernet 1/6-7” will change the setup interface to Port 6-7 and all the following commands will

be applied to Port 6-7.

If “vlan” sub-command is used, the setup interface will be changed to some VLAN groups. For example,

“(config-if)# interface vlan 100” will change the setup interface to VLAN 100 and all following commands will be

applied to VLAN 100.

The description of commands in interface configuring mode is put in Section

6.2.4 Interface Configuring

Commands

. Please refer to the section for the details.

command

This command is used to set IP address of the switch on this VLAN interface. And only users in this VLAN can

access this switch with the IP address remotely.

(config-if)# ip address ?

dhcp Dynamic host configuration protocol

A.B.C.D IP address

renew Renew IP

release Release IP

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды