CTC Union GSW-3208M Скачать руководство пользователя страница 119

Страница: 119 / 148

Chapter 6. Manage / Configure the Switch

119

1-3). VLAN Stacking

VLAN Stacking function allows two VLAN tags in a packet for 802.1Q VLAN tunnelling application through a central network.

For VLAN Stacking operation, port role definition is needed for each port. There are three roles for a port - Normal,

Tunnel, and Access.

Normal - It will set the port(s) as normal 802.1Q VLAN port(s). And the tagged/untagged setting will follow the

settings in 802.1Q VLAN.

Access - It will set the port(s) as access port(s) for VLAN stacking operation. It will strip a tag from tagged or double-

tagged packets before forwarding. It is for downward connection of VLAN stacking operation.

Tunnel - It will set the port as tunnel port for VLAN stacking operation. It will add a tag and allow two 802.1Q VLAN

tags in a packet. It is for tunnel and upward connection of VLAN stacking operation.

SPVID is used as the Port VLAN ID of VLAN Stacking (L2 Tunnel) operation if the port role is “access”.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды