CTC Union GSW-3208M Скачать руководство пользователя страница 10

Страница: 10 / 148

Chapter 3 Configuration and Operation

Chapter 3. Configuration and Operation

3.1 Connecting Devices to the Switch

[ Connection Guidelines: ]

For 10BaseT connection : Category 3 or 5 twisted-pair Ethernet cable

For 100BaseTX connection : Category 5 twisted-pair Ethernet cable

For 1000BaseTX connection: Category 5e or 6 twisted-pair Ethernet cable

For TX cable connection, always limit the cable distance to 100 meters (328 ft) as defined by IEEE specification

If your switch has 1000BaseSX/1000BaseLX connections, you can connect long distance fiber optic cable to the

switch.

Because this switch supports

Auto MDI/MDI-X

detection on each TX port, you can use normal straight through

cable for both workstation connection and hub/switch cascading.

3.2 Connecting to Another Ethernet Switch/Hub

This Switch can be connected to existing 10Mbps / 100Mbps / 1000Mbps hubs/switches. Because all TX ports on the

Switch support Auto MDI/MDI-X function, you can connect from any TX port of the Switch to the MDI or MDI-X port

of another hub/switch with Straight Through or Crossover cables. If the switches have fiber-optic ports, you can

cascade them with fiber optic cable.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды