CTC Union GSW-3208M Скачать руководство пользователя страница 27

Страница: 27 / 148

Chapter 6. Manage / Configure the Switch

11.

copy

command

This command is used to backup system configuration/firmware to TFTP server, restore system configuration from

TFTP server, and update firmware from TFTP server.

# copy ?

binary-config Copies binary configuration file

config Copies configuration file

firmware Copies run-time firmware

copy binary-config running-config tftp xxx.xxx.xxx.xxx yyy

command is used to backup current switch running

configuration to TFTP Server at IP “xxx.xxx.xxx.xxx” as file name “yyy” in binary format.

copy binary-config tftp running-config xxx.xxx.xxx.xxx yyy

command is used to restore binary configuration file

“yyy” from TFTP Server at IP “xxx.xxx.xxx.xxx”.

copy config running-config tftp xxx.xxx.xxx.xxx yyy

command is used to backup current switch running

configuration to TFTP Server at IP “xxx.xxx.xxx.xxx” as file name “yyy” in text format.

copy config tftp running-config xxx.xxx.xxx.xxx yyy

command is used to restore text configuration file “yyy” from

TFTP Server at IP “xxx.xxx.xxx.xxx”.

copy firmware running-firmware tftp xxx.xxx.xxx.xxx yyy

command is used to backup current running firmware

to TFTP Server at IP “xxx.xxx.xxx.xxx” as file name “yyy” in binary format

copy firmware tftp running-firmware xxx.xxx.xxx.xxx yyy

command is used to update the running firmware file

“yyy” from TFTP Server at IP “xxx.xxx.xxx.xxx”.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды