CTC Union GSW-3208M Скачать руководство пользователя страница 47

Страница: 47 / 148

Chapter 6. Manage / Configure the Switch

6.2.4 Interface Configuring Commands

Commands in Configuring Mode are for general switch settings. And its prompt is “(config)#”.

The port interface function and VLAN group interface function are set with “interface” command.

(config)# interface ?

ethernet Ethernet port

vlan Switch Virtual LAN interface

interface ethernet 1/x

command is used to configure settings for

Port x

. Please refer to section

6.2.4.1 Interface

Configuring Commands for Port

for the details.

interface vlan x

command is used to configure

VLAN Group x

interface (“x” is the VLAN ID). Please refer to section

6.2.4.2 Interface Configuring Commands for VLAN

for the details.

Both commands will change the prompt from “(config)#” to “

(config-if)#

”.

Note:

The general VLAN settings are done with “

vlan database

” command. Please refer to section

6.2.5 VLAN

Configuring Commands

for the details. And

interface vlan x

command is used to assign characteristics to a VLAN

interface. For example, assigning IP address to a VLAN interface is done with this command.

6.2.4.1 Interface Configuring Commands for Port

Commands in Configuring Mode are for general switch settings. And its prompt is “(config)#”.

If the settings are for ports, it is done with “

interface ethernet 1/x

” command in configure mode. For example,

“interface ethernet 1/5” is for settings on Port 5.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды